Найдено 50 результатов
- 07 май 2024, 23:16
- Форум: Прошивка для приемника на базе SI473x
- Тема: Доработки оригинальной схемы ATS25
- Ответы: 73
- Просмотры: 17890
Доработки оригинальной схемы ATS25
Hi Antonino, Thank you for the information. The circuit you have shown does not seem to be correct. The NPN transistors needs to be removed as per the example in your Github page. Mixer.JPG Mixer enable, GPO2 = Logic ‘1’ (3V3). N-Channel MOSFET ON, PNP transistor ON, Relay ON. The solid state versio...
- 03 май 2024, 13:46
- Форум: Прошивка для приемника на базе SI473x
- Тема: Доработки оригинальной схемы ATS25
- Ответы: 73
- Просмотры: 17890
Доработки оригинальной схемы ATS25
This will not work automatically unless you come up with a different switching scheme for filters. The minimum that can be done is to switch manually to connect the mixer. Hi, All understood. It just seems strange that GPO2 was chosen for the mixer control if it is already being used for filter sel...
- 03 май 2024, 13:02
- Форум: Прошивка для приемника на базе SI473x
- Тема: Доработки оригинальной схемы ATS25
- Ответы: 73
- Просмотры: 17890
Доработки оригинальной схемы ATS25
Hi, For interest, does the ATS25 Max Decoder II use GPO2 for its HF filter selection? The generic diagram generated for the mixer arrangement implies the following truth table. Mixer.JPG If like the ATS25-AMP, the ATS25 Max Decoder II uses GPO2 for its internal HF filters depending on frequency (i.e...
- 03 май 2024, 00:12
- Форум: Прошивка для приемника на базе SI473x
- Тема: ATS-120
- Ответы: 93
- Просмотры: 13364
ATS-120
Hi,
When the radio rebooted after the firmware update, there should have been an option to set the receiver type.
You should be able to go into SETUP/CONFIGURATION/Choosing a model and then select the ATS120.
73, Dave
When the radio rebooted after the firmware update, there should have been an option to set the receiver type.
You should be able to go into SETUP/CONFIGURATION/Choosing a model and then select the ATS120.
73, Dave
- 02 май 2024, 18:13
- Форум: Прошивка для приемника на базе SI473x
- Тема: ATS-120
- Ответы: 93
- Просмотры: 13364
ATS-120
Hi,
Looking at the screen dump, there does not appear to be a COM port specified.
I may be mistaken, but if you run the batch file manually you will need to pass it the arguments for the ‘COM’ port and the ‘DISPLAY’ type.
Example: flash COM3 ili9341
73, Dave
Looking at the screen dump, there does not appear to be a COM port specified.
I may be mistaken, but if you run the batch file manually you will need to pass it the arguments for the ‘COM’ port and the ‘DISPLAY’ type.
Example: flash COM3 ili9341
73, Dave
- 01 май 2024, 22:27
- Форум: Прошивка для приемника на базе SI473x
- Тема: Баги в прошивке v4.2
- Ответы: 26
- Просмотры: 3624
Баги в прошивке v4.2
Specifically a mixer, or SI5351? It's strange, somehow I don't quite understand the connection - modulation and mixer... Do you use it for demodulation in any way? For FM demodulation, the FMI input is used on the SI4732. Therefore for CB/10M NFM the input signal needs to be upconverted (using the ...
- 01 май 2024, 17:43
- Форум: Прошивка для приемника на базе SI473x
- Тема: Доработки оригинальной схемы ATS25
- Ответы: 73
- Просмотры: 17890
Доработки оригинальной схемы ATS25
I have the same module as in the picture of the respected Darwin (download/file.php?id=161&mode=view). If I don't need to extend the range, but only want stability and accuracy of frequency setting, can I use the circuit from his post above ⇈ without any NE602 mixer? Device ATS25 max-Decoder II...
- 29 апр 2024, 17:39
- Форум: Прошивка для приемника на базе SI473x
- Тема: Доработки оригинальной схемы ATS25
- Ответы: 73
- Просмотры: 17890
Доработки оригинальной схемы ATS25
Hi Darwin, For the expanded frequency modification, both the SI5351, NE602 mixer circuit and associated RF switching would be required. The on-board crystal is connected between SI4732 (GPO3 - Pin 2) and (RCLK - Pin 13). When using the SI5351 for the frequency reference, the crystal would need to be...
- 27 апр 2024, 01:00
- Форум: Прошивка для приемника на базе SI473x
- Тема: Доработки оригинальной схемы ATS25
- Ответы: 73
- Просмотры: 17890
Доработки оригинальной схемы ATS25
The scheme has an error, pins 1 and 4 on the BL1551B chip have been replaced. Hi, Yes, I agree that the previous schematic shown looks incorrect. From the layout information (Ref: https://github.com/IU4ALH/IU4ALH/tree/main/PCB's), the BL1551B switches appear to be connected as shown in the diagram ...
- 23 апр 2024, 10:27
- Форум: Радиолюбительский приемник ATS25
- Тема: Полоса пропускания BANDW
- Ответы: 5
- Просмотры: 728
Полоса пропускания BANDW
Hi, Perhaps the information in the attached link will cover your question. An extract is shown below. “When I got my first typical (Silicon Labs 473x-) DSP portable I started wondering about the filter choices: The widest filter setting showed familiar “6 kHz” in the display but it sounded so much w...